Response SA5 E Instruções de Operação Página 20
- Página / 52
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
20
12. If for any reason you need to disable the Siren,
remove jumper link P3 on the circuit board. This
will prevent the Siren from sounding during an
alarm condition. However, the Siren will still beep
to acknowledge signals from the Remote Control,
(provided the beep feature has not been disabled).
P3 tted Siren enabled
P3 removed Siren disabled
13. To enable the Jamming Detect feature in the Solar
Siren t the jumper link taped to the cover of the Siren
control unit across link pins P1 on the circuit board.
P1 tted Jamming Detection enabled
P1 removed Jamming Detection disabled
14. Ret the DIP switch cover and replace the 3 cover
xing screws. Do not over tighten the screw as this
could damage the thread.
POWERING UP THE SIREN
Connect the 9V PP3 power-up battery to the battery
clip.
1. Connect the rechargeable battery to the charging
leads. Connect the Red lead to the Red ( + ) terminal
and the Black lead the Black ( - ) terminals. Both
indicator LEDs will ash together in a single long ash
to indicate that the unit is operational.
2. Press the tamper switch, both indicator LEDs
will ash together several times. The LED’s will
then continue to ash alternately every 10 seconds
thereafter to indicate that the Siren is functioning.
3. Hinge the front cover locating tabs over the top
edge of the back plate and carefully push the base of
the siren cover into place. Secure the Siren cover in
place by retting the xing screw in the bottom edge of
the cover. Do not over tighten the screw as this could
damage the thread.
IMPORTANT: Ensure that the rear tamper switch
is closed when you t the siren cover to the back-
plate (i.e. listen for the switch to click). If the
switch does not close it will prevent the Siren from
operating correctly. If necessary, remove the siren
cover again and adjust the screw on the back-plate
tamper plunger to ensure the switch closes when
the Siren is secured in position. If tted remove the
protective lm covering the Solar Panel.
Testing the Solar Siren:
4. Use the and buttons to scroll through
the menu until ‘ALARM TEST’ is displayed and press
. .
5. Scroll through the menu until ‘WIREFREE SIREN
TEST’ is displayed and press .
The solar siren should activate for a period of
approximately 5 seconds.
6. Press to return to the top level menu of
Test Mode.
IMPORTANT: The Siren must now be left in position
for at least 24 hours to fully charge the Main Battery
before testing or operating the alarm.
EXTERNAL CONNECTIONS
- 6 Zone Communicating 1
- Wirefree Alarm System 1
- Tools and Equipment Required: 2
- CONTENTS 3
- KIT CONTENTS 4
- INTRODUCTION AND OVERVIEW 5
- button on their 6
- 7
- 7
- 7
- TYPICAL INSTALLATION 8
- REMOTE CONTROL UNIT 9
- Testing the Remote Control: 10
- INSTALLING THE CONTROL PANEL 11
- Inside View of Control Panel 11
- At the Control Panel: 12
- Using a Remote Control: 12
- PASSIVE INFRA RED (PIR) 13
- MOVEMENT DETECTORS 13
- PIR DETECTOR 14
- Testing the PIR Detector: 15
- 1 2 3 4 5 15
- MAGNETIC CONTACT 16
- DETECTORS 16
- + side is uppermost on each 17
- EXTERNAL SOLAR SIREN 18
- SOLAR SIREN 19
- . 20
- User Access Code 21
- FACTORY SETTINGS 23
- Master User Access Code 24
- LEARN SYSTEM HOUSE CODE 27
- ALARM DURATION 27
- to save and exit, or 28
- RINGS TO ANSWER PHONE 29
- DIALLER DELAY 29
- DIAL METHOD 29
- DIAL MODE 29
- ZONE SETUP 30
- FINAL EXIT SET 31
- ENTRY DELAY 31
- Delay Period 31
- PART-ARM 1 32
- PART-ARM 2 32
- WALK THROUGH 32
- TELEPHONE NUMBERS 33
- ALARM MESSAGE PLAY TIME 34
- RECORD ALARM MESSAGES 34
- REPLAY ALARM MESSAGES 34
- CALL ROUTING 34
- TEL CONFIRM TIMES 34
- EXIT-DELAY PERIOD 35
- ENTRY-DELAY BEEPS 35
- EXIT-DELAY BEEPS 35
- CALL ATTEMPTS 35
- TIME & DATE SETUP 38
- LATCH KEY SETUP 38
- 39
- ANSWERPHONE ON/OFF STATUS 39
- TELEPHONE NUMBER: 40
- REPLAY ANSWERPHONE GREETING 40
- OPERATING INSTRUCTIONS 41
- LEAVING A VOICE MEMO MESSAGE 43
- External Answerphone: 43
- Control Panel 45
- Remote Control 45
- PIR Movement Detector 45
- Magnetic Contact Detector 45
- MAINTENANCE 46
- ALARM RECORD 47
- Symptom / Recommendation 48
- EXTENDING YOUR ALARM SYSTEM 50
- GUARANTEE 50
- 01268 563273 52
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Response SA5 E
(24 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais