Response RE3000S Instruções de Operação descarregar pdf (Página 23)

When fully armed the Full Arm LED will be illuminated

steadily.

PART ARMING THE SYSTEM

If you are remaining in the premises, you may arm all

the Zones which have not been omitted, by selecting

Part Arm. This will permit free access to the omitted

Zone areas.

The system may be set on ‘Part Arm’ either at the

Control Unit or using a Remote Control Unit. If setting

on ‘Part Arm’ at the Control Unit, you must first Enter

your 4 digit access code (Main User or Second User

Code) then press . Alternatively, if Quick Arm has

been programmed, press and hold the button for

5 seconds. If arming from the Remote Control Unit,

simply press the orange Part Arm button.

The LEDs associated with the Part Arm Zone(s) will

illuminate for 5 seconds. (Any Zone LED not lit indicates

that that Zone has been omitted and will not be active in

Part Arm mode). After the 5 seconds the LEDs will

extinguish and the Part Arm LED will illuminate steadily

to indicate that the system is Part Armed.

You must leave all protected Zones before expiry of

the 5 second arming time. If for any reason you are

unable to leave the protected areas within the arming

time, you will need to disarm the system then re-arm.

Failure to do so will cause a full alarm if any protected

door is opened or movement is detected by a Passive

Infra Red Detector set to operate in Part Arm.

When part armed, the Part Arm LED will be

illuminated steadily.

DISARMING THE SYSTEM

Upon entering an Entry Delay Zone, the Control Unit

sounder will emit an intermittent bleep tone and the

appropriate Zone LED(s) will flash for the Preset

Entry Delay period.

You may disarm the system by pressing the blue

disarm button on the Remote Control Unit or by

proceeding immediately to the Control Unit and

entering your 4 digit Access Code (Main User or

Second User Code) followed by .

Note: If the system is not disarmed during the Entry

Delay Period a full alarm will occur. When using the

Remote Control Unit, you may be able to disarm the

system from outside the premises before entering.

Establish the operational range of the Remote Control

Unit before using this method.

DISARMING AFTER AN INTRUSION

A full alarm condition (Control Unit Siren and external

Siren and Strobe operating) will be initiated following

an intrusion. This condition will continue until expiry of

the preset ‘Auto-Stop’ and/or ‘Alarm Duration’ times,

whereby the Control Unit Siren and external Siren and

Strobe respectively will cease. The Appropriate Zone

LED(s) will flash to indicate the Zone(s) which triggered

the alarm. The Control Unit will now immediately re-

arm itself. In the event of a further intrusion the Control

Unit will once again initiate a full alarm condition and

the above process is repeated.

If a full alarm condition is initiated accidentally the alarm

can be cancelled immediately by pressing the blue

disarm button on your Remote Control or by entering

your 4 digit Access Code (Main User or Second User

Code) followed by at the Control Unit.

IMPORTANT

Following disarming of the system after an Alarm

activation, make a careful note of the zone LED

indications to assist with tracing the cause of the

alarm. The Control Unit MUST then be reset by

entering your 4 digit Access Code (Main User or

Second User Code) followed by .

The system CANNOT be rearmed until the Control

Unit has been reset.

PERSONAL ATTACK,

MEDICAL AND FIRE

ALARM

A full alarm condition can be initiated by the user at

any time (system armed or disarmed) in the event of

threat or danger as follows:

PERSONAL ATTACK:- Press the red button on

your Remote Control.

The Control Unit will initiate a full alarm and Zone 8

LED will flash.

RE5000S Professional Alarm System 21

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 33 34

Comentários a estes Manuais

Sem comentários

Response RE3000S Instruções de Operação Página 23

Comentários a estes Manuais